Dark mode is

Forward Controls Design Optics Platform, Glock, for RMR (OPF-G, RMR)

Out of stock

Forward Controls Design Optics Platform, Glock, for RMR (OPF-G, RMR)

$64.60

OPF-G, RMR (Optics Platform, Glock, for RMR) is a Glock MOS Adapter Set 01 compatible plate for mounting Trijicon RMR or SRO on Glock Gen 4 and Gen 5 slides, G17, G19, G34, G35, G41 (width 25mm/1 inch.)  It is incompatible with G40 that uses Set 02.


Forward Controls Designs like the Glock MOS concept, even if they find the factory MOS adapter plates could use some help.  Standards, commonality, availability of parts are all good things.  Before now, users have had to send in their slides to be milled to accept mini red dot sights, or opt for 3rd party optics ready slides.  The time it takes to send in the slides to be milled, and varying quality of the milling work and optics ready slides notwithstanding, there was a lack a standard regarding the sight height, it'd be a coincidence if two slides milled by two different shops share the same sight height.   Glock's MOS may not sit as low as some, but in our opinion, what MOS offers more than makes up for it, namely a uniform sight height, ease of installation, parts commonality and availability.


OPF-G, RMR is a collaboration with a USMC combat veteran and former USMC Shooting Team head coach, Tom Shields. Forward Control Designs used Glock's MOS adapter plates as a basis, and designed their version of what they think it should and can be.


OPF-G, RMR's shape follows its functions, same as all of Forward Control Designs products.  Forward Control Designs outlined the following objectives:

  • 1. Sight is to be fully supported in the front and rear by recoil lugs/fences, with minimum movement.
  • 2. Eliminate the need to use an additional sealer plate.
  • 3. Correct length sight to plate, and plate to slide screws.  Screws are to be Torx.
  • 4. Adapter plate is to be machined in steel.


OPF-G, RMR accomplishes all of the goals outlined above. OPF-G, RMR's thickness is unchanged from that of the Glock MOS plate, it doesn't change the sight's mounted height, nor does it require different iron sights.


As Trjicon RMR and SRO share the same mounting footprint, OPF-G, RMR is also compatible with SRO.   However, due to the precise fit of the front and rear recoil lugs/fences that are designed to closely sandwich the sight, OPF-G, RMR is incompatible with Holosun sights.  OPF-G, H will be available as a separate product.


OPF-RMR is shipped with plate to slide screws (M3-0.5mm x 6mm, same as what Glock MOS plates uses), and sight to plate screws (6/32 x 3/8), a T10 key and a VC3 packet.


Weight: 0.83oz

Plate to slide torque value: 13 to 15in/lb

Sight to plate torque value: 13in/lb


OPF-G,RMR supports the full width of the RMR and SRO, a sealer plate is not necessary.  If a sealer plate is used, it will reduce the thread engagement of the sight to plate screws for no gain.


OPF-G, RMR is designed to sandwich the sight in its front and rear fence, Forward Controls makes the spacing as close to Trijicon's dimensions and tolerance as they can.  Though they hold a 0.003 tolerance, Trijicon's estimated tolerance is 0.005.  In practical terms, this means while some RMRs will move inside the fences by a very small amount, others will need to be forced into the space.


Proudly designed and made in the USA.


NOTE: this version is incompatible with G40 (10mm) that uses Glock MOS Adapter Set 02.

More Information
SKU OPF-G-RMR
Manufacturer Forward Controls Design