Dark mode is

Tactical Springs (Sprinco) M4 Carbine Buffer Spring and Extractor Spring Kit

AR-15 Part

In stock

Tactical Springs (Sprinco) M4 Carbine Buffer Spring and Extractor Spring Kit

As low as $21.95

All of Sprinco (Tactical Springs) springs are constructed from Certified Chrome Silicon wirestock to ISO 9001:2008 quality standards to withstand extreme heat and highly cyclic rate. The certification rating ensures a consistency in the parent material of 95%, which translates to repeatable consistency in performance & function. Certified Valve Quality Chrome Silicon wire is used in very high stress applications such as, NASCAR, Formula One, Moto GP & Pro Stock racing motor valve springs. It is not uncommon in some of these applications for valve springs to see 15,000,000 compression cycles in one race. It is this extraordinary capability that makes Chrome Silicon wire the obvious choice in our spring production vs. music wire or 17-7 PH used in OEM springs and by most aftermarket competitors. In addition, all of our Chrome Silicon buffer springs are heat treated, stress relieved, and dual-stage shot peened in separate post winding treatments. They also treat each spring with a proprietary, deep-penetrating, Re-Micronized (to .3 Micron particle size), inhibited, Molybdenum-Disulfide (MoS2) formulation to eliminate 90% of all mechanical wear on the spring. The combination of materials & processes result in a loss of no more than 5% in spring efficiency. The minimum anticipated duty cycles of our buffer spring designs are in excess of 1,500,000 cycles.


ADVANTAGES:

  • Shortened "lock time" for faster sight recovery and platform stability

  • Consistent spring pressure throughout the duty cycle of the spring, resulting in fewer malfunctions related to spring operation. (Especially Type III malfunctions)

  • Improved & consistent cyclic operation. Spring will not change performance for many hundreds of thousands of rounds.

  • Greater resistance to heat induced performance degradation

  • Reduced cyclic rate with Enhanced or Extra Power springs and reduce / eliminate bolt bounce with optimal spring / buffer weight selection.

  • Reduced operating cost as replacement springs are not needed during the life of your upper receiver assembly. Less downtime and fewer trips to the armorer for spring replacement, in fact, this will most likely be the only buffer spring you will ever need for the duty cycle of your carbine or rifle!

  • Correct spring selection works reliably, consistently, and virtually indefinitely in all properly built and maintained AR platforms.


"WHITE Spring" STANDARD Power Buffer Spring. Equivalent spring load to a “fresh” Mil-Spec M4 Carbine Spring. This spring will perform reliably in any properly configured and maintained 5.56 Carbine, if you wish to maintain the performance of a “fresh” Mil-Spec load spring without concern for replacement. This is the best choice for shooters and purists that wish to maintain the performance of most factory supplied NEW Mil-Spec springs, but do not wish to be concerned with frequent replacement of same or do not have the time or inclination to seek enhanced performance options. The "WHITE" spring is recommended for 10.0"-11.0" SBR's with H2 Buffers, 1st Gen M&P's, older RRA's with under 18"+ BBL's, early generation Colt 6920 LE's, 5.56 & 6.8 SPC 7.5"-8.5" BBL Piston Guns with H2 Buffers, with few exceptions, most .300 AAC Platforms, longer carbine barrels using intermediate or rifle length gas, and when training with SRTA and other low power and light charged “budget” rounds. Color Coded WHITE. [EXCEPTIONS: With SBR's which are seriously overgassed firing suppressed, (e.g. 10.3" HK 416's), a RED or ORANGE along with a hydraulic buffer is often used with great success.]

“BLUE Spring” ENHANCED Power Buffer Spring, Offers improved performance with most non-suppressed 12.5"-14.5" SBR's, 16" DI Mid-Length BBLS, and all mid-length uppers with adjustable gas blocks. Best performance is usually achieved using buffers ranging from ST-2T, H2, DPMS Extra Heavy Buffer. Will run in 18"+ Length BBL RRA'S with ST-T2 Buffers. Color Coded BLUE

“RED Spring” EXTRA Power Buffer Spring, Best option for 16"+ 5.56 barrels with carbine length gas system platforms with standard front sight towers and H buffers, 16" + BBL gas piston guns, *some* suppressed shorties,and later generation Colt LE6920's, 9mm, 6.8 SPC, 6.5 Grendel, .458 SOCOM, 450 Bushmaster, .500 Beowulf, and assorted "Thumpers" using standard 7" depth M4 extension tubes. AR-10 Carbines (E.G. Armalite, Noveske, LMT) using deeper extension tubes and standard length carbine buffers to accommodate the longer .308 BCG also use the "RED" Spring. Please call us to discuss successful historical "recipes" for implementation of the RED spring in .308, 6.8 SPC, etc. RIFLE length extension tube platforms. Color Coded RED. NOTE: NOT for use in .308 Carbines using standard 7" M4 extension tubes and short, stubby buffers. (Use our "ORANGE Spring" below for that specific platform approach application.) NOTE: If you have a seriously overgassed .308 Carbine which has the deeper AR-10 platform receiver extension tube running an H3 buffer firing 175 Gr. Projectiles and / or suppressed, many shooters have experienced success using the "ORANGE" spring, as it is still heavier than a "RED" spring in that application. 

"ORANGE Spring" The ONLY specifically engineered EXTRA POWER Buffer Spring for .308 Carbine Platforms using standard 7" Depth M4 extension tubes and .308 short 2.5" buffers (Including aftermarket "heavy buffers.") You cannot clip coils from any other commercially available buffer spring to yield the proper spring loads for this application, especially in heavily gassed .308 carbine platforms. We started from scratch on this design to provide Operators with a viable alternative to existing OEM and aftermarket offerings. Platforms known to exist using this approach include DPMS, Bushmaster (Post 2010), Remington, CMMG, Mega, SA Defense, Colt 901, Rock River Arms and many others. Color Coded ORANGE

"GREEN Spring" In addition to use in 5.56 Fixed Stock Rifles, our “GREEN Spring” is just the ticket for use in the VLTOR A-5 Stock System using their appropriate weight buffer for maximum versatility in tuning almost any upper configuration, running both with or without a "can". Color Coded GREEN

Buffer is inserted into color coded end of spring for fast I.D. of installed spring by Operator. 


Sprinco (Tactical Springs) take their extractor springs one step further with the addition of Cryogenic Processing. This computerized, ultra low temperature process (-320°F) increases the strength & wear life of the parent material through a change in microstructure resulting in less retained austenite and more uniformity in grain structure.


ADVANTAGES:

  • 5-Coil XP spring higher load than OEM springs, thus negating the need for a D-Fender™ ring

  • Enhanced 4-Coil springs maintains the load of a NEW Mil-Spec Spring and is recommended for use in 18" +BBL lengths for those who retrieve their brass for reloading. While the 5-Coil XP spring is totally reliable for all 5.56 BBL lengths, it can be aggressive on case rims on longer length BBLS and may be too strong for some bolts with extremely tight bolt face tolerances (E.G. AR Performance 6.8 SPC precision machined bolts.)

  • Extreme duty cycle while maintaining performance specifications.

  • D-Fender™ rings are NOT recommended for use with our 5-Coil extractor springs. Use with either black extractor spring insert OR CRANE Viton O-Rings.

  • Dual spring .308 XP extractor spring sets may be used with or without CRANE O-rings

  • Plug & Play - May easily be the only extractor spring needed for the life of your bolt!!

More Information
SKU M4-SPRING-KIT
Product Type AR-15 Part
Manufacturer Sprinco (Tactical Springs)